Näytä suppeat kuvailutiedot

dc.contributor.authorKoivu, Viivi
dc.date.accessioned2010-10-07T12:44:21Z
dc.date.available2010-10-07T12:44:21Z
dc.date.issued2010
dc.identifier.isbn978-951-39-4033-1
dc.identifier.otheroai:jykdok.linneanet.fi:1137251
dc.identifier.urihttps://jyx.jyu.fi/handle/123456789/25461
dc.description.abstractThis thesis deals with creeping fluid flow through fibrous porous materials. Permeability through a porous medium is a measure of the ability of the material to transmit fluids. For testing and demonstration purposes the permeability values of a few fibrous heterogeneous materials, namely synthetic non-woven felt, wet pressing felt, cardboard, newsprint and hardwood paper, were measured experimentally. Reconstructions of the same materials under similar compression states were captured by x-ray micro-tomography. The actual microscopic pore structure thus obtained was utilised in the numerical lattice-Boltzmann analysis for solving the fluid flow permeability of the materials. Agreement between the experimental and numerical results was good. In addition, numerical permeability results for certain geometries were compared to the values obtained by finite-difference and finite-element methods. All numerical results were found to be in close agreement. The resolution of the tomographic reconstructions is limited causing discretisation uncertainty in the numerical analysis. The reliability of the numerical results was estimated by performing simulations for high and low resolution lattices. These results were further compared to the corresponding analytical solutions. The discretisation uncertainty was found not to be essentially larger than the typical total uncertainty of the experimental results. The advantage of the combination of x-ray tomography and numerical methods arises in the cases where direct experimental measurements are not feasible. An example of such an application, reported in this thesis, is to analyse the permeability of individual, distinct layers in a layer-structured material in order to determine the contribution of this layer to the overall permeability. In the final part of the work, tomographic reconstructions of porous heterogeneous materials were combined to a void space segmentation analysis. The utilisation of the method was demonstrated by running the analyses for a series of tomographic reconstructions of liquid packaging boards. The methods facilitate e.g. the analysis between the structural characteristics of pore structure and their relation to imbibition process. Demonstration analyses indicate the void space segmentation analysis to give valuable information on correlations between the structure of porous heterogeneous materials and their fluid flow properties.en
dc.format.extentxiv, 74 sivua :.
dc.language.isoeng
dc.publisherUniversity of Jyväskylä
dc.relation.ispartofseriesResearch report / Department of Physics, University of Jyväskylä
dc.relation.haspart<b>Artikkeli I:</b> Koivu, V., Mattila, K., & Kataja, M. (2009). A Method for Measuring Darcian Flow Permeability of Thin Fibre Mats. <i>Nordic Pulp and Paper Research Journal, 24(4), 395.</i> DOI: <a href="https://doi.org/10.3183/npprj-2009-24-04-p395-402"target="_blank"> 10.3183/npprj-2009-24-04-p395-402 </a>
dc.relation.haspart<b>Artikkeli II:</b> Koivu, V., Decain, M., Geindereau, C., Mattila, K., Alaraudanjoki, J., Bloch, J.-F., & Kataja, M. (2009). Flow permeability of fibrous porous materials. Micro-tomography and numerical simulations. In <i>Trans. 14th Research Fundamental Symposium, Oxford (S.J. I’Anson, ed.), September 14-18 th, 2009, FRC, (pp. 437).</i>
dc.relation.haspart<b>Artikkeli III:</b> Koivu, V., Decain, M., Geindreau, C., Mattila, K., Bloch, J.-F., & Kataja, M. (2010). Transport properties of heterogeneous materials. Combining computerised X-ray micro-tomography and direct numerical simulations. <i>International Journal of Computational Fluid Dynamics, 23(10), 713-721.</i> DOI: <a href="https://doi.org/10.1080/10618561003727512"target="_blank"> 10.1080/10618561003727512</a>
dc.relation.haspart<b>Artikkeli IV:</b> Koivu, V., Seppänen, R., Turpeinen, T., Mattila, K., Hyväluoma, J., & Kataja, M. (2010). Combining x-ray micro-tomography and image analysis to study imbibition and void space in liquid packaging board. <i>Journal of Pulp and Paper Science, 36(3-4), 1-8.</i>
dc.relation.isversionofISBN 978-951-39-4032-4
dc.rightsIn Copyright
dc.subject.othermikrotomografia
dc.subject.otherhuokosrakenne
dc.subject.otherfluidivirtaus
dc.subject.othersingle phase fluid flow
dc.subject.othercompressible porous media
dc.subject.otherpermeability
dc.subject.otherimbibition
dc.subject.otherlattice Boltzmann method
dc.subject.otherx-ray micro-tomography
dc.subject.otherpore structure
dc.titleAnalysis of fluid flow through porous media based on x-ray micro-tomographic reconstructions
dc.typeDiss.
dc.identifier.urnURN:ISBN:978-951-39-4033-1
dc.type.dcmitypeTexten
dc.type.ontasotVäitöskirjafi
dc.type.ontasotDoctoral dissertationen
dc.contributor.tiedekuntaMatemaattis-luonnontieteellinen tiedekuntafi
dc.contributor.tiedekuntaFaculty of Mathematics and Scienceen
dc.contributor.yliopistoUniversity of Jyväskyläen
dc.contributor.yliopistoJyväskylän yliopistofi
dc.contributor.oppiaineFysiikkafi
dc.relation.issn0075-465X
dc.relation.numberinseriesno. 9/2010
dc.rights.accesslevelopenAccess
dc.subject.ysoaineen ominaisuudet
dc.subject.ysofysikaaliset ominaisuudet
dc.subject.ysohuokoisuus
dc.subject.ysoläpäisevyys
dc.subject.ysoimeytyminen
dc.subject.ysoröntgensäteily
dc.subject.ysovirtauslaskenta
dc.rights.urlhttps://rightsstatements.org/page/InC/1.0/


Aineistoon kuuluvat tiedostot

Thumbnail

Aineisto kuuluu seuraaviin kokoelmiin

Näytä suppeat kuvailutiedot

In Copyright
Ellei muuten mainita, aineiston lisenssi on In Copyright